Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
We are using SDK nRF5_SDK_13.0.0_04a0bfd with the NRF52832 chip. Using peripheral role, the nRF is fatal crashing right after connecting with iOS nRFConnect (and our custom...
Hello. I have discovered similar questions, but it's still not clear for me. I also have cheched pwr_mgmt example, but as I understand all operations with power mode in board...
I recently upgraded from SDK 11.0 to SDK 14.0 and am seeing much slower connection speeds from the new SDK. The old version would connect in about 400ms, but the new SDK takes...
I would like to measure the VDDH voltage (lithium ion battery) on a nrf52840 with the power fail comparator.
If the voltage drops below the threshold, I want to reduce the...
Hi all,
we are using NRF52810 and SDK 15.0 (our own custom board)
working on ble_app_uart.c example.
we are able to send / receive 20bytes(approx).
we need to transfer...
In my project, I aim to send an ADC value (10 bits ADC) and 6 data (16 bits/each data) from MPU6050 by using nrf51 DK to Android app ( modified from https://github.com/NordicPlayground...
Hi,
Using the nRF52832 device with the S132-v4.0.2 soft-device (s132_nrf52_4.0.2_softdevice) (So customized that two nRF52832 devices with the same Soft-Device interact...
Hi,
I do the FreeRTOS Blinky sample, works fine and I do the BLE Client/Server sample, works also fine.
Is there any sample combining FreeRTOS with a SoftDevice (132 for...
Hello,
I referred a Softdevice 130,310 & 132 Specification, from where i noticed that softdevice includes Host & Link Layer (As a part of Controller).
So, i want to ask...
Hello,
I'm working with 3 servers, 1 client and 1 provisionner ( 4 nRF52832-DK + 1 android with NRF Mesh App ).
Client side : light switch proxy_client example Server...
hi!
I use the reference design of nrf52832_ciaa.IntLib ,but it didn't work
I use the internal-LDO ,but i measure the voltage of DEC4, it's 2.5V(not 1.3V), the VDD is 2...
Hello,
I am developing a BLE application using the custom characteristic example provided by nordic. I have added a few characteristic for the same.
I am having a small...
I am just trying to establish communication between spi master and spi slave.
I am using two nrf52 boards, SDK 15, in one i dumped spi master example and in another i dumped...
Hi,
I have a customer developing with the nRF8001 with an external MCU, a PIC32MM. He is interfacing the the device with SPI and he is struggling to set up the device and...
