We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to work with VL53l0x distance sensor. Basic communication working good, but i am not able to get distance...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
I've been through the tutorial of connecting the NRD52 board to my PC, but my PC isnt recognizing it at all. No pop up for any usb devices. I've tried different cables and...
Dear Nordic Team,
Thanks for supporting.
currently i am try to interface MMA8453 accelerator with ble proximitty example .Already i have interfaced peripheral example...
Hello, I am new to NRF. and actually i dont have other MCU experience, beside adrduino.
my question is not about BLE/BLE+,
it's more about how to use NRF5283 in keil question...
SDK 13 Alpha
The header guard in serialization/connectivity/codecs/s132_s140/serializers/ble_l2cap_conn.h looks like this:
#ifndef BLE_L2CAP_CONN_H__
#define BLE_L2CAP_CON__H__...
Hello,
I really like the new nRF52840, especially it's Bluetooth 5 capabilities. The thing is that i cannot figure out if i would be able to make nRF52840 based devices...
Hello,
I have tried to debug ble_app_uart_pca10040_s132 application included in nordic SDK12.2 with Segger Embedded studio v3.12, but even though I don't get error while...
