Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
I have a nRF51822 Evaluation kit I am trying to get up and running. My kit has the older QFAACA part.
I followed the steps to setup eclipse and GCC and i am successfully...
Hello,
I took the ble_app_hrs rebuilt it and used Control to verify all is correct. I also tested it with the nRFTools Android App and it works fine I see temperature changing...
Hello,
I am currently starting with the hole ble topic. This forum helps me a lot in the last weeks to understand ble.
I am using S110 to provide a peripheral device...
I use the nRF51422 with S310 stack and i found the nRF51422 power consumption are quite different after connection on different phones which run the Master Control Panel as...
I have written some code that uses the SPIS to transmit data. One of the bursts is constant, for example I have a fixed sequence to send using the SPIS and so if I define...
Hello.
I use nrf51822 EK and custom board.
I have to replace the bd address i can not be found in the ble_app_ibeacon_bcs source code.
Is it any way to fix the bd address...
Hi. I'm curious if there's a way to filter devices in the "Discovered Devices" list while scanning with MCP. We have a lot of BLE devices in our office, so the list is fairly...
Hello, I am looking for the way I can use PWM to control duty cycle of connection. I am really novice and my understanding about programming and Bluetooth protocol is really...
I'd like to use the pin sense function as the power switch of my NRF51822 device. That is to say, after the very first power cycle (reset or battery change), the device goes...
Hi everyone,
I am trying to learn nrf51822 using Keil,
I need a very simple program to learn such as:
function bluetoothhandle(value)
{
if(value=="test1")
{
bluetooth_write...
Hi,
I tried to combine BLE HRS & UART together on nrf51822. The service initialization code is
void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;...
Hi,
I am trying to get the PWM example ( github.com/.../nrf51-pwm-library) to work with a Softdevice (S110) that advertises.
There have been several Questions on the...
hi hakon, you told me to do " Try using the variable, for instance by setting "rx_info.rssi = rx_info.rssi;" in the callback and see if that helps." in the question i have...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
