Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am running into an issue with the Fstorage Library with SDK14 that I did not have using SDK12.
When I am not connected to BLE I can erase and write flash with no issues...
Hello,
I am trying to make BME280 sensor work with nRF51 DK. I just need temperature readings. So i searched if there was some examples using this sensor and i found this...
Seems PPK is broken, it measures ~70mA no matter what I connect it to, even only measuring on a DK in shutdown.
I suspect this happend during measuring on a custom board...
Hi We are making a project where we use Bluetooth mesh, which works fine, but we have a problem with TWI (slave), the problem is when we want to read what is on the slave...
when i use dsm_address_publish_remove() to remove a group address , it will show MESH ASSERT when i restart the board.error code is NRF_ERROR_NOT_FOUND when execute dsm_address_publish_add_handle...
I read on ANT documentation that is possible to configure different channels with different network keys.
In my project i write:
>> sd_ant_network_address_set( "ANT+NetworkNumber...
Sorry I must have missed some crucial bit of documentation.
I have some code working using GPIOTE, however the inputs of the hardware, that will connected cannot be driven...
Hello,
I have interfaced MPU accelerometer on i2c and GPS on UART. Have enabled UART and using printf to display both sensor data. To begin with, both work fine individually...
Hi,
I checked erratas for nRF52840 rev1 and #164 is gone but #191 is still there. Can I have both #164 and #191 active in my code and it won't cause problems on either engineering...
Hello,
I have a question regarding the nrf uart driver. The RXTO event is never triggered even though the Interrupt itself is enabled (and the line is idle after a packet...
hi,
In Light switch Example ahead of time he have 3 Servers so we set SERVER_COUNT=3
if I want to develop Mesh Network..Where I introduce new Node, Provision the node...
when i use other hex file, it appear every time.
after i click "yes"， i can't scan the divece?
so what the proble ? how can i use "nRF Connect " with other hex file ,...
Hi everyone.
I want to use the nRF8001 in a low power application and therefore I want to save as much energy as possible.
I read in other discussions that the nRFgo studio...
