Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
My application goes to system off by using nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF). In the handler, I configure a sense to be woken up by a GPIO, as...
Hi all,
I have a nrf52832 board from holyiot ( https://pl.aliexpress.com/store/product/Nordic-nRF52832-module-Bluetooth-low-energy-development-board-for-BLE-mesh/420533_32867403706...
Hi,
I'm trying to use an existing NRF51822 mbed codebase on a new NRF52832 product and am having some issues.
First of all, it seems that I can't use mbedlib, but need...
Hi all,
I have a Gateway with nrf52832 BLE chip-set.
My question is: Does this chip-set provide the ability to get the RSSI levels of the three advertisement channels...
At the bottom of page 15 in nRF52832 Product Specification v1.4 the following reference is printed:
[1] See GPIO located near the radio on page 17 for more information....
Hi,
If event is not handled (or handled but EVENT register not cleared), will it go above 1 or is it binary?
In other words, can the value be used to detected missed...
I am attempting to port code from sdk 11 to 15. Some of the code is __older__ and in need of updating. A line which runs during the application init calls the sd_ble_version_get...
Hi!
I have added programs for register writing to SPI programs and using SDK14.0.0
I am using the nrf_drv_spi_transfer function to transfer three data.
but when confirming...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi!!
I am now using SDK 14.0.0. and I have added UART functionality to the SPI program().
I could confirmed that SPI and UART can transmit data separately.
However,...
Hello,
I am trying to modify the ble_app_uart code so that my peripheral can send data automatically to the central, which in turn can print it on a computer through UART...
