Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I'm combing over the CLI peripheral example, but having a few problems when running the example:
The Debug Terminal in SES blacks out the test so its difficult to see...
Hi I have developed and Android application to connect for 2 BLE Devices one after other.
These 2 BLE devices connection and service discovery will happen one after the...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if central can make connection request without scanning (central know the mac address...
Hi everyone,
I have migrated my project from SDK for Mesh v2.1.1 to v3.0.0.
I am getting a Mesh Assert when the Mesh is trying to request a radio timeslot after the "NRF_EVT_RADIO_BLOCKED...
Is it possible to run Eddystone example from SDK12.3.0 on nRF51822 xx aa chip?
In the eddystone documentation it mentioned that S132 softdevice required, but on older SDK...
Dear Nordic,
Hi,i'm looking for an easy way to make Wlan coexistence with Ble,i know there has a solution that named 3rd party, just like this:
So, What i want to...
when we pass the BLE event handler as a function argument to BLE stack init function and register the function results in a deadlock mechanism. Is that we cant able to register...
Hi Guys,
I have a general question to the mesh functionalities. We built a mesh sensor network and I now want to now if it is possible to decrease the data-rate to increase...
Hi,
I just completed the migration from mesh sdk 2.2.0 to 3.0.0.
After running the project it get stuck at line 422 of timeslot.c in function timeslot_sd_event_handler...
Hi all,
So I've developed a custom board with the NRF52832 qfaa e1 and using Mbed OS 5. System on current is around 3.5uA when not using BLE.
When using BLE my idle current...
I'm learning NRF51822.Now,I want to develop it with PC.I need connected Nrf51822 & PC with Ble.What tools can I use? .I designed a Nrf51822 pcb based on CH340.
Hi,
I am using nRF52840-QIAA-T in my design. I am curious to know if Engineering B modification is implemented in the mentioned package.
Thanks in advance.
Hi i used nRF52840 Preview-DK and i try many example with SDK provided.
the problem is the range of transmission too short . can you help how to set power transmission of...
I’m creating an IOT device with some unusual needs when compared with typical home automation. I wanted to ask if anyone knew of a mesh protocol (Zigbee, Thread, BLE Mesh...
Hi All,
I am working on the NRF51822 development board, using KEIL-IDE for the code development using SDK version 10.
I was trying to develop the serial communication...
