I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
Hi Sir
We'd want to do RX testing with DTM mode, however, the dtm example code looks can't report receive data or total packets counts,
So that, we don't know how to determine...
Hello,
I'm using the nrf15822 chip and am using the ble_app_uart example from nrf5_sdk_12.2.0.
I know softdevice will automatically generate random numbers through RNG...
I've been told due to PAN 58 it is not possible to use EASY DMA with nrf52832 without switching to the deprecated SPI driver. Is there a workaround that allows the use of...
Hello,
We are going start custom PCB design by using nRF52840 chip and SDK 15.0, but confused for use 3rd party nRF52840 modules or design complete custom PCB using componenets...
Hi,
Despite knowing a fair bit of the theory of wireless comms (mainly PHY and MAC), I'm brand new to actual hardware configuration/protocol development, so please be gentle...
As a master device with a whitelist there is a limitation on how many slave devices can be connected. If i am correct, other than whitelist there is no restriction to the...
Hi,
How do I receive data from host (computer) on my BLE device(Nordic board)? I want to use a simple open source HID API to send data to Nordic board and glow an led or...
Hello, we have finished all prototyping with BLE modile from Taiyu Tuden, this module: https://www.yuden.co.jp/wireless_module/document/datareport2/en/TY_BLE_EYSGJNZ_DataReport_V1_9_20180530E...
Good day, I am new to this forum so I am having some problems posting my question. Sorry for any inconveniences. I am having serious problems flashing my custom NRF5282 board...
I want to connect nRF52832 with PC. The objective is using nRF52832(I am using BT832 Module) I have to scan all Blue Tooth deceives details and send to PC. Please help with...
Hi,
I am using a custom board with the nrf52832 with SDK 13 and I have a bootloader and an application that both configure and feed the WDT.
However, upon restart (power...
Is there any straight forward way to detect jamming using any technique on this Nordic device? I'm using SDK 15.2, Soft-Device 6.1 Would this be possible by the new SD 6 function...
