Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hey all,
I've been having a problem that it seems like a few others have had as well. When I connect my desktop computer to the devkit, it does not respond to any nrfjprog...
HI, I am using NRF52832 sdk15.2 .
I have some doubts
How to assign two to three different timers to do different functions
1. I need to read the sensor data every one...
Hello,
I'm working on a BLE central project where we want to utilize LESC Just Works Unauthenticated pairing.
I followed the recommended usage guide at https://www.nordicsemi...
Hi,
I am using nrf_fstorage_sd which uses nrf_atfifo. I would like to know what it is max usage of m_fifo queue so I can set lowest NRF_FSTORAGE_SD_QUEUE_SIZE value. I figured...
I develop an program with BLE DFU support, but we hope to merge all hex as single hex file. Then we can burn this hex file by programer (such as jlink or NRF52DK), So we have...
Hello,
I'm trying to run the s132 (and s140) softdevice while running a proprietary mesh network stack. Naturally I'm requesting a hefty amount of radio slots. I need to...
Dear Nordic,
I have an application which contain UART and BLE advertising. For power consumption i use enable disable UART.
Enable and Disable Uart:-
Is it right way...
hi..
i am using nrf52832 and a peripheral device .. temperature sensor ,my temperature values are increasing like(0 ,27,75,80...) how to get a approximate value .
i have...
Platform: nRF52832 using SDK12.2 and Keil 5.20a
I've encountered strange corner case when displaying negative floats using NRF_LOG_DEBUG .
My test code looks like this...
I want to use BLE 4.2 Data length extension to stuff more data into one packet. I am looking at the "ble_app_att_mtu_throughput" example and am getting confused because there...
Hi!!
I am sending data by BLE data received by SPI.
The interval for sending data at BLE is 64 ms.
I have written and run NRF_SPI 1 -> ENABLE = 0; and NRF_SPI 1 -> ENABLE...
can't open 'J:/Projects/..../Electronics/SDK/BT840F/nRF5SDK15209412b96/nRF5_SDK_15.2.0_9412b96/examples/ble_central_and_peripheral/experimental/ble_app_att_mtu_throughput...
If there are multiple beacons, let's say B1,B2,B3,B4,B5 and a BLE receiver. I want receiver to only wake up from sleep mode when B1 transmits(long broadcast interval) and...
Hello Nordic community,
is it possible to configure the network key, application key, node address with the help of a byte array? The keys, adresses and all the peripheral...
