Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I've seen other users on the DevZone have had a similar problem ( link1 link2 link3 ), but none of their solutions have been able to resolve my problem.
I'm using the...
Hello Nordic
My device is consuming ~4mA in normal (I already use function "sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)" )
As i know that the current SDK mesh v2.1.1...
Hi,
We are working on Android O with SR3 v1.1.
There is an issue that our Android STB can't find any BLE device using your library.
( https://github.com/NordicSemiconductor...
HI
[environment] · NRF 51822 · SDK 12.3
We are developing application software including DTM.
In the application software, a flag to start DTM using FDS is written in...
Hello all,
I've recently started developing an nRF5 device (using Segger on Ubuntu, and SDK15.2.0), and for what I have read regarding peripheral drivers, I should be...
Hello all!
I'm trying to optimize power consumption for project based on nRF51802 and external host MCU. My current platform and toolchain:
1. nRF51802 as Bluetooth controller...
Hello, i am using NRF52840 board with NRF52840 SDK version 15.2 with softdevice 140 Version 6.1. I am using the BLE_NUS_UART_C example and id like to send a scan request to...
Dear nordic,
BLE advertising happens in 3 channel(37,38,39) and scanner scans these channel based on scan interval consecutively
I want to scan single channel instead...
Using nRF Connect for both iOS and Android, the advertised name is the same for both apps, i.e, DeviceX.
Clicking on the device information also shows the Complete Local...
Hello,
I am using an nRF52840PDK (master) to use an SPI peripheral, where my code is based on examples\peripheral\spi. My IDE is Segger Embedded Studio and I am using SDK...
Hi Nordic Team!
Please find below attached the schematic for my custom nRF52832 proto board. The boards are already manufactured and are in the bringing-up stage. The designs...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
