We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I need to do pairing between the two 51822 modules. All the information I find is paired with the slave and the mobile phone. There is no host matching process demo or learning...
Hi
I'd like to create a firmware that supports multiple Nordic boards as Hardware (as the nRFConnect Firmware does). To do that I have to configure the peripherals according...
Hi,
I am trying to test an application running on the nRF52840 using your nRF Sniffer (actual version 2.0.0.2.beta).
My application should be able to request a change...
Hi,
As per the forum thread https://devzone.nordicsemi.com/f/nordic-q-a/37591/nrf-connect-for-desktop-max-throughput/144881#144881 there is a limitation in data acquisition...
Hello,
I have some questions about mesh network.
Current i am working with 10 Boards (nRF52840 modules) and i want to test the BLE mesh network. I have installed the software...
Hello,
I am currently trying to implement an IR sending functionality. My plan is to use a timer to toggle gpiote through ppi. For the width of an IR pulse (or mark) and...
Hi, it's my first post in this forum, and I glad to join to Nordic Community.
After few month of developing project on Nordic MCU, I try to migrate form SDK 12.2.0 to SDK...
Is the nrfutil pkg --hw-version N a customized hardware version, or is it the nrf chip family number (e.g. 52 for nrf52832)?
Both the help and the manual are a bit unclear...
Hi,
I have merged nrfx_spim with uart in nrf52840 dk (PCA10056) board .i am able to transmit only string but not integers. from my sensor i use spi to send real-time integer...
Hi,
May I know which version of S140 SDK and softdevices support which version of Amazon FreeRTOS and FreeRTOS kernel? If yes, I'm interested to know, as far as I know I...
Hello there,
I'm developing a C++ application on the BLE654 development bord which shall be able to generate and send 100+ BLE notifications per second on a single BLE connection...
Hi,
I need to compile the BLE_Connectivity project for pc-ble-driver. I've followed the below document:
https://github.com/NordicSemiconductor/pc-ble-driver/blob/master...
Dear Nordic Semiconductor Team,
this is the same question as in https://devzone.nordicsemi.com/f/nordic-q-a/40957/att_read_by_type-when-bonded
i accidentaly closed it...
