Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I have modified the ble_app_hids_keyboard_pca10040_s132 example to enumerate as a Gamepad and Modified the GPIO so the buttons send a USB report.
I am now trying to integrate...
Hi,
I am doing some customization for the secure DFU example (SDK15) and i want to add conditions for the update process (battery level for example).
I wonder if there...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
Hello, In one of my codes, I use the printf function. It works properly when implemented in the int main(void), but when I try to use it in a static void NAME (void){} function...
Hello,
I'm checking the DTM code from nRF5 SDK15.2.0.
In the ble_dtm.c file, line 763:
And in the ble_dtm.h file lines 104-110:
DTM_PKT_0XFF and DTM_PKT_VENDORSPECIFIC...
Hi.
We got Thingy for power measurement purposes. I tried first the it out of box and it works fine. Same with pre-built image.
However if I build the SDK example and...
non connectable advertise success when in SDK 8.0.0, however I got error code 0x00000007 when upgrade to SDK 9.0.0.
I find out error code 7 is NRF_ERROR_INVALID_PARAM,...
hi,
my development kit nrf52832 is not detecting via phone nrf connect app . it appears like no device found .i flashed the ble blinky example program (sdk 15.2version)...
Hi to everyone!
I recently bought the nRF52 SDK to use it in a project, but the kit contains a NFC antenna and I don´t know its use.
My project its about Bluetooth Mesh...
i use the sdk15.2.0, the chip is nrf52832,my device have both BLE peripheral,and BLE center in my application, I use center to connect with peripheral, i directly use the...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
