I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I have modified the ble_app_hids_keyboard_pca10040_s132 example to enumerate as a Gamepad and Modified the GPIO so the buttons send a USB report.
I am now trying to integrate...
Hi,
I am doing some customization for the secure DFU example (SDK15) and i want to add conditions for the update process (battery level for example).
I wonder if there...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
Hello, In one of my codes, I use the printf function. It works properly when implemented in the int main(void), but when I try to use it in a static void NAME (void){} function...
Hello,
I'm checking the DTM code from nRF5 SDK15.2.0.
In the ble_dtm.c file, line 763:
And in the ble_dtm.h file lines 104-110:
DTM_PKT_0XFF and DTM_PKT_VENDORSPECIFIC...
Hi.
We got Thingy for power measurement purposes. I tried first the it out of box and it works fine. Same with pre-built image.
However if I build the SDK example and...
non connectable advertise success when in SDK 8.0.0, however I got error code 0x00000007 when upgrade to SDK 9.0.0.
I find out error code 7 is NRF_ERROR_INVALID_PARAM,...
hi,
my development kit nrf52832 is not detecting via phone nrf connect app . it appears like no device found .i flashed the ble blinky example program (sdk 15.2version)...
Hi to everyone!
I recently bought the nRF52 SDK to use it in a project, but the kit contains a NFC antenna and I don´t know its use.
My project its about Bluetooth Mesh...
i use the sdk15.2.0, the chip is nrf52832,my device have both BLE peripheral,and BLE center in my application, I use center to connect with peripheral, i directly use the...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
