But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
IDE: keil uvision 5.23, SoftDevice 3.0.0, SDK 12.1
Computer Platform: Windows 10
Receiving device: nrf52832_xxAA
In our project, there is a sender always advertising...
Hi,
I have a project where, I need to change the minimum and maximum (MIN_CONN_INTERVAL and MAX_CONN_INTERVAL) connection interval to higher values like 1 second and 2 second...
hi everyone!
I am developing NRF52840 with the Development Kit.
I am trying to use a GPIO to o capture a external HIGH-TO-LOW signal and then trigger a LED.
I I learned...
Hi all,
I'm currently using nRF Connect in combination with a nRF52 DK to connect to my Mesh network. So right now I have to type all my commands as HEX messages and decode...
Hello,
I'm trying to compile the Light_switch_provisioner example (Debug, Mesh 2.2.0) in Segger Embedded studio.
<t: 0>, main.c, 561, ----- BLE Mesh Light Switch Provisioner...
hello
i wanted to send message using the simple message model with some modifications from client to server periodically but didn't know from where i should start , i tried...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
Hello All,
I am developing an application using Nordic nRF_SDK_15.0.0, in which I need to make my BLE peripheral device as a peer device which will get/set data from/to...
Hello,
I am developing application for nRF52832 based SoC using nRF_SDK_15.0.0. I need to develop number of custom characteristic using given sdk. For reference, I am using...
Hello.
I'm trying to understand how to programm my nRF52 DK (PCA10040 - Rev 1.2.1) with SEGGER Embedded Studio (in Windows 10 - x64), however I can't follow all the tutorials...
