After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
I'm working with :
- nRF mesh SDK 2.1.1
- light_switch_proxy_server
- I implemented the generic model on / off
I work with a module (server) that has two...
i got this error when i am porting the code for nrf52810.i am working on the spi protocol i am porting code from nrf52832 to nrf5810. I am done the as per instuction given...
Hello,
We are currently using RTC1 and RTC2 to keep track of various times. RTC2 is our dedicated clock to keep track of time. I want to ensure that indeed, our application...
Hi All.
I need to add to Generic Access service such characteristics as Peripheral Privacy Flag (0x2a02) and Reconnection Address (0x2a03).
Does SoftDevice give an opportunity...
Hello everyone,
I would like to extend one of my program to use the new features of the BLE 5.0. It works in broadcast mode with BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hi Nordic,
I'm starting a project using the Thingy 52 and I'm going to connect Thingy with another sensor.
I have four communication options from the sensor:
UART, I2C...
Hello,
I'm using the buttonless DFU bootloader examples with bonding and the PC nrfutil with a nRF52840 PDK for the firmware upload.
If I try to start the DFU process...
I'm running SDK 14.0.0 and notice in the examples/flashwrite, the very last flash page is chosen as the place to write data to. Are there any caveats to that? WIll this location...
Hi, everyone. Long time no see.
I wonder if there is a free IDE which is official recommended. As we know that Keil and IAR are all commerical software. GCC command line...
Hello everyone,
As we know the proxy protocol is defined to include BLE devices in a mesh network. But as per my understanding there has to be made some changes in the...
Hello,
I am using nRF52840 PCA10056 DK i want to make my board as central device and scan for all nearby ble devices and display it's device id on terminal connected via...
Using SCAN_INTERVAL and SCAN_WINDOW at 1600 vill make the flash write and erase come out with a error, the fstorage is working fine before the SD is initialised.
/** @brief...
Hi,
I am using the secure bootloader as a template and I want to use the inactivity timeout to shutdown after 10 minutes.
I saw that the limit should be 60000000 ms (according...
SDK: nRF5 SDK for Thread and Zigbee 1.0.0
I have code for the SAADC based on the Low Power SAADC example here .
I have modified it to sample 4 inputs, and changed the...
