I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Aim: transfer large data coming from UART to nRF52832 over BLE 5.0 as fast as possible. Want to use 921600 baud rate in the case given below.
Scenario:
SDK: 15.2.0 ...
Hello there!
I'm developing an application that uses BLE to access the flash memory of a nRF52832, using RTOS Zephyr 1.10.0. The OS is Ubuntu.
JLinkRTTClient gives me...
Dear Nordic,
I want to achieve long range in my custom board
I have some doubts:-
1. is it any difference in schematic for achieving?
2. Which HF crystal i used...
Hello, I was wondering how can I send data continuously over NUS.
I am using the ble app_uart and app_uart_c to program two NRF52382 with s132. My goal is to sample a signal...
Hi
SDK 15.2.0 ch_map[5] is 5 bytes long so 40 bits. Can you please confirm if ....
ch_map[0] bit 0 corresponds to channel 0
ch_map[0] bit 7 corresponds to channel 7...
the Product Specification v1.4 of the nRF52832 SoC. On page 23 the RAM0 block section 1 address is given as 0x21001000. From the context I believe, this should instead read...
Development Kit - nrf52 DK
SDK - 15.0.0
Computer Platform - Windows 7 - 64 Bit
My application was working fine until I decided to change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello everyone!
I have a question regarding where should I place NRF_DFU_SINGLE_BANK_APP_UPDATES flag. Should it be inside sdk_config.h in a bootloader or application? Or...
How to enable and disable FreeRTOS tickless idle(RTC or Systick)? Anyway to wakeup from tickless idle mode when there is BLE activities detected?
Setup:
1. nRF5_SDK_15...
Compiled Blinky client fails on Dongle PCA10059.
Precompiled version nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
I am trying to compare a bunch of BLE mesh options and I am trying to evaluate the software stack for nRF mesh
Whilst trying out the light switch proxy example, I noticed...
Hi Great Nordic Team:
I have some questions about nrf24ap2 reference schematic, please kindly help to give me some tips.
※it's reference circuit of Synchronous (bit...
Hi Sir,
As reference below link, and we can find the Tickless IDLE enabled ~700uA in SDK 15.2
https://devzone.nordicsemi.com/f/nordic-q-a/24733/nrf52840-sdk-14-0-0-and...
Hi again!
I'm trying to send/receive data between an nRF51(master) and a AVR/HM-11(serial/BLE module)(peripheral)
After following this visualgdb.com/.../ tutorial based...
Under some conditions I want to force advertising to transition from slow to fast. With SDK 14, I could just call ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST)...
