Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
When reading about access_opcode_t struct on its infocenter page it stumbled upon this table i don't understand.
access_opcode_t is defined as:
Data Fields
-------...
I'm employing 51822AA.
I need to debug firmware for this chip line by line. Like environment of ARM9 with Lauterbach TRACE32 through JTAG.
Is line debugging possible...
From application point of view, when should I use UICR and when should I use Flash storage? I have studied the documentation and the functionality seems very similar. The...
Hi everyone,
I trying to make a flash jump on Nrf51822 in my project. there are 2 programs(program A and program B) below. i am working on to make program A jump to program...
Hi everyone,
I'm new with nrf52832, and I need to measure elapsed time in microsecond between rising edges of 12 different Gpios. I have 12 piezoelectric sensors filtered...
Hi,
I have used nRF52840-PDK.
And I want to test profile and protocol with PTS.
I succeeded in GATT-based service test and GATT test with PTS.
But when I try to L2CAP...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
I try to add default nRF sdk libs in Segger studio. All files exist and path corect.
in nutshell i try to add uart module to default ble_app_buttonless_dfu example
Hi ,
I'm looking for BLE Specification but I just found NRF52 Datasheet on Nodric page . Can you give me this document , It will help me a lot . Regards !!!
Hello All
I am planning interface the BLE peripheral + Capsence(Atmel QT111) board
i did the Capsence Board with Spi Protocol..then second phase i has to implement with...
Hello
I have some problem that I want to change Characteristic UUID different from Service UUID.
Like,
Service UUID : 11111111 - 1111 -1111 -1111 -111111111111
Charcteristic...
Hi Nordic,
I used FDS to operate updata to update data more than 10K once, but there was an error. Hint FDS_ERR_RECORD_TOO_LARGE.Can FDS operate more than 10K data at once...
I want to create own android app with just nus service (uart).I'm not very good in android programming, so there are two ways for me doing that:
Use Android-nRf-uart...
