hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello mates,
I am modifying the Light Switch Client and Server example, to send messages uint8_t from the client to the server instead of use bool on_ff with no luck yet...
I am currently using a 51dk board. I am trying to study low power system_on_wakeup_on_gpio in github. I built this code and measured the amount of current. I would like to...
Parameter setting code is shown below. I've verified that the settings are being reported back in events, so they seem to be taking place. However, I'm keeping track of the...
I am trying to get the application to enter DFU via the buttonless DFU service using SDK 15.2. It appears to be stuck because of an SVC call not returning. Both application...
Hi :)
I would like to test the nRF52840-Dongle in a Raspberry Pi 3B+ OS = Rasbian (the bluetooth 5 features: 2Mbps and Long range). but unfortunately I didn't find a nRF...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
Sir
We have a client that is using two NINA B3 (uses a NRF52840), one central and other peripheral. The peripheral is sending advertising packages, but the central is only...
Hi I'm very interested in studying this protocol, and I'm testing with nrf52832 kit development, loading the example "bike power meter tx" and app on android "ant + plugins...
Hi,
I'm using NRF52832 and a core adaptation for Arduino IDE. In my project I'm using both TWI and SPI interfaces. If for TWI I manage to reduce the current during sleep...
Hi everyone,
I am using a chip nRF52832 reading data from LIS2DH12 via TWI (all in a custome boad), then data will be send to Master nRF52832 DK ia BLE_NUS. However, when...
I have a new nRF52840 Dongle which seems to have either had a hardware failure while updating its bootloader or the updating was unsuccessful and now the device does not flash...
To do some test, I need micros(). This is the reason why I couldn't use RTC or app_timer.
When I tried timer example(nRF5_SDK_12.2.0_f012efa\examples\peripheral\), I could...
Hello, I need to use PWM to control GPIO and integrate it to work on simple COAP server app using nrf52840 DK.
I used "pwm_simple" example from SDK (not Thread/Zigbie SDK...
Hello.
When I try to initialize provisioning bearer gatt with turned on the proxy, provisioning bearer is reconfigure the mesh_gatt which it will not work with proxy anymore...
Hello,
I started developing a Thread-Solution with my NRF52840-DK. Now I'm searching if there is a Message Sequence Chart (like for the BLE solution) also for the Thread...
