Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi ,
The nrf connect for desktop programming works good on my desktop before.
The tool shows error message "cannot find module 'usb' " today.
I ever try re-install the...
I am working on integrated peripheral and central device used for indoor positioning. The device has two modes, at boot it is a peripheral for some duration of time then it...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
Hello,
I try to control led light of the thingy52 throw a MIT app inventor application.
I use the UUID : ef680300-9b35-4933-9b10-52ffa9740042
and thr characterixtic...
Page 362 of nRF52840 product specification version 1.0 March 18 shows A in 5 bits. The max entry is 0x0D (4 bits) and there has to be room for 8 entries in 32 bits. Hence...
hello, is there any way to generate DFU package without using command line. i am using segger embedded studio can directly generate dfu package in segger embedded studio please...
What is the wake time for module if i put module in system off mode in following cases .
case 1: Module will wake up by GPIO signalling
case 2: Module will wake up by...
Hello,
I need more details on DFU mode entering topic. I understand how to configure DFU to enter the bootloading mode on button press event but have dilemma about using...
I’m doing a project using NRF51822. We use P0.06 pin for PWM out while reading ADC from P0.01 P0.02 P0.03 & P0.04 .
As my experiment, when I’ve used P0.01 P0.02 P0.03 &...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
