I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hello, Excuse me! I used the LFRC,the calibration interval of which is 8s, in my application on NRF52832. In order to measure the power consumption,I want to know the duartion...
Hi,
As well know, nRF52832 can use "16Mhz base-clock to output PWM signal, and it is very simple to create 4Mhz, 2Mhz, 1MHz signal output,
But, If I want to output a...
I'm trying to get a stripped down, simple LED blinking sample to work (like blinky) when building with GCC however main() is never called. I'm guessing I'm either using the...
I'm trying to take a project we had working with only an application, no softdevice or bootloader, and add a bootloader and softdevice, with the application still not requiring...
I am working on nrf5_SDK_for_Mesh_v2.2.0 with nRF5_SDK_15.0.0 and softdevice 6.0.0. I run code on PCA10040 dev boards. I am trying use a timer to send onoff message from a...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hello Nordic experts,
I am working with nRF5_SDK_15.2.0_9412b96 SDK.
In example nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_hrs_freertos/main.c I have at line...
Hi all,
The setup that I am aiming for has a number of nodes, which will send the IMU data to a central base station. The communication is achieved using a bunch of nRF24L01...
I keep getting stuck in the TIMER1_IRQHandler function.
When I debug the code, I get to line 20 (exiting interrupt function scope) and then the assembly code hits a nop...
Hello!
I have developed a BLE HID (HOGP) device in Nordic SDK 15.0.0 starting from an example project: ble_app_hids_keyboard .
The HID device that I have developed however...
We have a setup where we want to measure the current consumption of a battery-powered device:
The batteries are soldered to the device, and cannot be removed.
We can...
Dear Team,
i hope you are doing good,
I am working on nrf51822 controller, using SDK is 12.3.0 on windows environment. Soft-device is s130
i am planning interface...
Hi,
Wanted to interface NRF52840-DK to Board Mount Basic Pressure Sensors (Honeywell) ABPDANT005PGAA5 which is of anlog output type.Can u suggest can i go ahead with the...
hi......
my peripheral device is heating up quickly what is the way to reduce or avoid heating of the device ?
when i put my device in sleep mode more than the wake up...
Using SDK_14 and unmodified SAADC example on pca10040.
Initially connected A0 (PO.03) to ground but getting seemingly random values.
<info> app: ADC event number: 586...
