Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
I am trying to choose a BLE device for my upcoming biomedical product design. Any help in comparing these 2 devices will be greatly appreciated.
Things I am concerned about...
Hi,
I am using the nRF51822 with an external chip. The nRF51822 has interrupts which trigger when one of the signals from the external chip goes low. When using BLE and...
My program does a lot of dynamic memory allocation and at some point "malloc" retruns NULL , which is cause the system running out of allocated heap memory (I am assuming...
Hi,
i am newbie to nrf51822 and want to know details of following stuffs:
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there...
Hi guys,
i asked a similar question [1] few days ago, but yesterday i stumbled over the "service_data" type when advertising packages.
I've written a custom service...
Is there a specific part code for the latest Rev 3 QFAC silicon for the nRF51822? We were trying to track down a source with stock of the latest chips, but most resellers...
I'm having trouble using the RTC1 COMPARE function to generate an event/interrupt when the processor has been put to sleep using sd_app_evt_wait().
My configuration is...
Is it possible to use the nRF51 dongle as a slave ?
I have a nRF51422 Eval board that I am planning to use as a central device. Can I use the nRF51 as a slave so that I...
