I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I have previously bought a Evaluation kit, (now obsolete) and registered with it. I have also designed a new custom board with version 3 silicon, but I cannot download v8...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
How to flash SoftDevice and Bootloader (OTA enabled) to nrf51822 by CMSIS-DAP programmer?
For instance: I did cmsis-dap programmer with mbed code form github.
Can I do that...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
I know this was asked before, but none of the posts address my problem. There is a similar thread , but the issue on that one was that the softdevice was not being used. I...
Hi all,
I'm implementing a Bootloader with the source code provided no the website (Windows C# app, nRF24LU1 station app and nRF24LE1 device bootloader/app). Everything...
Hello,
When using the nRF Master Control Panel I see other Beacons with "Complete Local Name"... I am building an iBeacon but have not found a way to set the name and have...
The following thread talks about CPU unblocking during connection intervals.
devzone.nordicsemi.com/.../
How does this feature affect BLE Radio Notification? Do...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
