Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
I am trying to choose a BLE device for my upcoming biomedical product design. Any help in comparing these 2 devices will be greatly appreciated.
Things I am concerned about...
Hi,
I am using the nRF51822 with an external chip. The nRF51822 has interrupts which trigger when one of the signals from the external chip goes low. When using BLE and...
My program does a lot of dynamic memory allocation and at some point "malloc" retruns NULL , which is cause the system running out of allocated heap memory (I am assuming...
Hi,
i am newbie to nrf51822 and want to know details of following stuffs:
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there...
Hi guys,
i asked a similar question [1] few days ago, but yesterday i stumbled over the "service_data" type when advertising packages.
I've written a custom service...
Is there a specific part code for the latest Rev 3 QFAC silicon for the nRF51822? We were trying to track down a source with stock of the latest chips, but most resellers...
I'm having trouble using the RTC1 COMPARE function to generate an event/interrupt when the processor has been put to sleep using sd_app_evt_wait().
My configuration is...
Is it possible to use the nRF51 dongle as a slave ?
I have a nRF51422 Eval board that I am planning to use as a central device. Can I use the nRF51 as a slave so that I...
Hello we have developed a few products which have required (costly) RF/RFPHY testing.
Is there a reference design that is qualified that can be used to avoid the RF/RFPHY...
Suppose a BLE central needs to get sensor data from 10 peripheral sensors. Given that there is a limit to the number of connections a BLE central can have, is it better for...
Has anyone managed to get this revision of the nrf8001 IC working?
i bought 280 of them and none of them seems to work as it should.
When i reset the chip i get no interrupt...
