I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I made a board without external 32kHz crystal.
So, I changed NRF_CLOCK_LFCLKSRC source to NRF_CLOCK_LF_SRC_RC, which is used in ble_stack_init.
Now, I need to make DTM...
Hi,
I am use Exclusion list for my one application.
Exlusion list work is ok,but i am facing problem for how clear Exclusion list ?
My Controller: nRF514222 Rev 3,...
This is my first time working with a microcontroller and working with C as well, my only previous experience being C++ done in notepad on Linux. Currently I'm trying to just...
To reduce nRF52 design thickness, I'm planning to use a low profile inductor on the DCDC converter.
The low profile inductor has a higher resistance, compared to the recommended...
Hi, All.
Once I wrote data in NV memory, it's OK. I can get the same data I put in.
But, after power off - on reset, data are invalid. It's all 0xff(erased state).
I used...
Hi,
I have been trying to do it and even though I have generated packages using the old nrfutil and the new 1.5, when I use nRF connect to do the upload it aborts without...
I programmed my beacon with this code:
ble_app_beacon.zip
I use nrf connect app to see its signals. nrf connect can find my beacons but it says:
serviceUUID : N/A
TxpowerLevel...
Hi all,
I believe it should be possible to defined a characteristic which can be written to but have no automatic write response ACK sent. Instead I want to send a manual...
I develop a temperature sensor sending a temperature and battery status every second.
Used to work fine on previous nRF Toolbox.
Today on my Android 6 and latest nRF Toolbox...
Difficult to obtain the high-ohmage resistors in the solar beacon reference design. Will 5% resistors suffice or do the resistors have to be 1% tolerance.
I have difficulties understanding the COMP APIs, this function below starts after initializing the COMP the peripheral.
nrf_drv_comp_start(NRF_DRV_COMP_EVT_EN_CROSS_MASK...
I am using the nRF51822 utilizing the internal LDO setup. I received a question during regulatory submittal that I am not able to answer and am looking for help on. Is the...
Hi
I've tried to update some of our environment to the SDK12 files. When I tried to compile some of the files a weird bracket error showed up.
At the end i could find...
Hi,
I'm trying to run one of the template app programs from the Nordic SDK 12.0 library with a nRF52832 board as my target. I had trouble with compiler errors using the...
