I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
We tried to run the blinky example in the contiki source tree, and we had a strange behaviour. The example code is here , and the hardware is here .
The issue is...
Hi,
I'm using a RF module with nRF24L01+. Sometimes the RF stop working, the module keep replying status of no rx data (all pipes).
The device is embedded into a device...
Hello
I'm testing latest examples on 10040 (SDK12 S132). I want to get autoConnect working on Blinky example with nRF Connect app but I'm unable. Has anyone tried this...
HI all Nordic Developers,
Recently, I am using nRF51 DK as a beacon scanner connected to my laptop (Baudrate: 115200), it works fine to detect the beacon broadcast from...
HI,
I am using development board of BLE nRF52832 battery which you provide CR2032 is support for good battery backups
please give the reasons behind in it?
Hi all,
Is the "to-be-sniffed" advertisement packet allowed to have incorrect CRC, or perhaps a missing CRC? I.e. Is it possible for the sniffer to just display the raw...
Hello,
A problem occurs when i run the DFU over UART on my board.My bootloader project references to nRF51_SDK_9.0.0_2e23562\examples\dfu\bootloader\pca10028\dual_bank_serial_s110...
ANT experts,
I have been looking at the nrf52 implementation of the ANT timestamp (and timesync) features. One thing that is rather puzzling is the fact that the documentation...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
Hi in my project I am using nRF5_SDK_11.0.0-2.alpha SDK, s132_nrf52_2.0.0-7.alpha_softdevice. and nrf52 DK board(PC10040).
My issue is, when I run the ble_app_uart example...
