Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I have a custom board which has NRF52832 SOC(i.e. main MCU) and another ARM Core-M0-based MCU(i.e. target MCU). These two are connected over I2C. I wonder how to...
nRF BLE sniffer is crashing within the first few minutes of use. Attached is the log of one sniffer
session from the start to when it crashes.
Here is my log.txt from...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
I have device with nrf5x and I will customize this device on production. I use to flashing nrfjprog.
Will prepare one hex file and customize e.g serial number during flashing...
Good time dear Engineers!
Faced with a general Problem.
I use two nRF52 boards connection : Central <-> Peritheral.
init data: MIN/MAX conn intervals = 10/30 ms
...
I noticed that the GPIO port read and port write for SDK v12.2 changed to accommodate chips with more pins but I can't find much information about it. How do I use nrf_gpio_port_out_read...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
With nrf Toolbox 2.2.1 on android 6.0.1 (Google Nexus 7 or OnePlus 3T), I try to transfer an application firmware in a zip file UiBoardV0.4.1.zip , generated with "nrfutil...
Hi,
In am using a nrf52832 in a serializated configuration, with the softdevice S132 on the connectivity board.
Is there a way to configure GPIO on the connectivity...
hello,
i have one nrf51 dk and it has some advertisement packet, i have another nrf51, i want this another nrf51 to copy first nrf51's data. can you tell me how to copy...
