I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
Hi, I want to change some configurations of my beacon such as packet type, UUID, Tx power and so on, in an online manner through the Bluetooth connection(by an application...
Hi I have run into this error when running. However it has just appeared (the FDS did work but now will not initilise.) I am using Visual_gdb.
As per this issue
I have...
Hi,
I am using nRF8001 with a MCU from PIC18F family. I have successfully configured nRF8001 to send and receive data through the nordic UART pipe (I used the app nRF UART...
I am experiencing a strange problem with stopping a scan. I am using the mesh from github.com/.../nRF51-ble-bcast-mesh together with interval scanning, meaning start scanning...
Hello Nordic developers,
I was tracing through the new SD init code in the HRS example app for nRF52 and followed this macro into softdevice_handler.h. Is it supposed to...
I am planning on using:
NRGF51822 CDAB WCSP (= 128KB Flash, 16KB RAM, 3.5x3.5mm)
Another main chip I will be using is:
LSM303AGR ( www.st.com/.../en.DM00177685.pdf)
...
Hi
In my application I have a function that takes about 1 ms, in which timing is critial.
(I cannot allow even a few us change of the timing inside this function).
When...
Greetings, and thank you ahead of time to anyone willing to lend some advice.
I'm implementing application-layer security by requiring central devices to supply a user...
