I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
Hi, I want to change some configurations of my beacon such as packet type, UUID, Tx power and so on, in an online manner through the Bluetooth connection(by an application...
Hi I have run into this error when running. However it has just appeared (the FDS did work but now will not initilise.) I am using Visual_gdb.
As per this issue
I have...
Hi,
I am using nRF8001 with a MCU from PIC18F family. I have successfully configured nRF8001 to send and receive data through the nordic UART pipe (I used the app nRF UART...
I am experiencing a strange problem with stopping a scan. I am using the mesh from github.com/.../nRF51-ble-bcast-mesh together with interval scanning, meaning start scanning...
Hello Nordic developers,
I was tracing through the new SD init code in the HRS example app for nRF52 and followed this macro into softdevice_handler.h. Is it supposed to...
I am planning on using:
NRGF51822 CDAB WCSP (= 128KB Flash, 16KB RAM, 3.5x3.5mm)
Another main chip I will be using is:
LSM303AGR ( www.st.com/.../en.DM00177685.pdf)
...
Hi
In my application I have a function that takes about 1 ms, in which timing is critial.
(I cannot allow even a few us change of the timing inside this function).
When...
Greetings, and thank you ahead of time to anyone willing to lend some advice.
I'm implementing application-layer security by requiring central devices to supply a user...
