Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
I used nRF24L01+ in an industrial control project that requires low power consumption. I have completed all the functional development and reliability verification. A problem...
NCS 2.6.1 + nRF52832
We are using the LIS2DH sensor driver from Zephyr. We observe (and this is also explicitly stated here ) that the sensor initialization is triggered...
Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
Hi, I have cloned the channel sounding with range requestor samples but every time I try to build it I encounter the error:
I have not changed the code or anything, but...
Hello Team,
I'm using nrf54l15 dk and ncs version 2.9.0 for the development. I am getting an error while configuring I2C. I selected i2c20 from the device tree and assigned...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello, I need help understanding how MCUBOOT produces signed_by_b0_app.hex file from app.hex on the network core of nrf5340. My goal is to have a DFU updatable hex file (net_core_app_moved_test_update...
Hey everyone! I'm working on my Master's thesis about Rust in embedded systems and trying to figure out how much Nordic Semiconductor actually backs the Rust community.
...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
Hi, I'm working with the nRF9151 DK and currently going through the Cellular IoT Fundamentals course. In Lesson 4 , it states that we should see a message indicating a successful...
Hi
Could you provide what is the max DCR value of L2/L3 10uH inductor in document "PCA20053_Schematic_And_PCB.pdf" that nRF5340 can be accepted?
nRF5340 datasheet only...
Hello! Introduction. Responsibilities of the cores in my device: 1. app core. 1.1. data processing from a stereo microphone 1.2. data sending to net core. 2. net core. 2.1...
I used to use UICR to store the serial number information during the production with nRF52832.
I am working on new project with nRF9151, but when I check the datasheet,...
