Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Having spent numerous hours/days on trying to get the SDK12 examples running on my nRF52DK board with MacOS SES3.12, I in result wrote a basic guideline that in the end makes...
Hi,
i search a FSK tranceiver with a ADC readout for a experiment.
I need the raw ADC ("audio") signal for a external signal processing.
Please help, most of the wireless...
I want to transfer application over the air(OTA) to NRF51822, with using nrf-toolbox in android mobile so please tell me step by step procedure. and how to setup nrfDK to...
hello every,do you have the same question?
i delete the bsp relevant document,then i find that when i disconnect it from APP,it delay to Generate disconnect events. i use...
I'm trying out 6lowpan examples in the IoT SDK, and while everything works,
if I want to disconnect by running:
echo "disconnect 00:50:49:71:3b:44 1" > /sys/kernel/debug...
I have compiled the following list of error that are given by BLE Stack from the ble_app_gls code.
I would like to know what action needs to be taken on reception of all...
Hi everybody!
I want to do a connection between two BLEnano, one is the mater and the second the slave.
I have programmed the two BLEnano using the Arduino IDE and libraries;...
Hello,
I was wondering what is the best option/way to merge two functionalities which are developed in different examples of the nRF52 sdk12.2.
For instance, I would...
hi,
my device is nrf52832
i run my spi sd card driver fine in debug mode, but when i download it ( F8 ), it can not work!
so my question is what is the difference...
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
I'm trying to get a simple "Hello world" program to run on the Nordic ID Medea.
As soon as I start debugging I get the error "The bootstrap could not be loaded".
Any idea...
I follow this:
developer.nordicsemi.com/.../a00092.html
Creating an image file
The format of the firmware image that you use to update the device firmware depends on...
