Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
I followed the Nordic tutorial on wrapping an SDK sample project in a Makefile managed Eclipse project. I used the ble_app_beacon as the project.
Eclipse will build the project...
I have implemented pwm as suggested in the info centre of nordiac semiconducter. But it showing the following error as shown below image.
Please Help if any one is aware...
Hi,
I think that I found bug in nRF Toolbox release 1.3.0.
1)Application flashing stucks on 95%
2)If you click on Abort, application will stuck in aborting phase. ...
Hi,
Currently I'm working on updating some code based op pstorage on the nRF51822 with SDK 10 an SD S110 (v8).
Right know we're not using "blocks". We're using pstorage_update...
Hi All,
Is there any way to extend RTC2 wakeup interval time more than 2s ?
we know that the maximum interval time of RTC2 on LE1 is 2s, i want to keep LE1 power donw to...
When I just test and build with NRF51-DK there are with BSP Package. such as (pca10028).
But When I make a new PCB Board, Do I have to make my own BSP Package (.h header...
Hi. I have a problem with HID keyboard example. Function sd_ble_gatts_hvx returns 0x00003401. I know that it's means BLE_ERROR_GATTS_SYS_ATTR_MISSING. But how and where I...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hello everyone.
I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
We have to pick a BLE very quickly , and up till now we used to work with modules which are expensive in mass but easy to work with (e.g RN4020)
I am looking for a chip...
