Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
Hello,
In our application, we do not use the antenna at Pin30.
However, in Nordic's Reference design in Github, even the simplest design (nRF52832_qfaa_dcdc) has an...
Hello,
Can I interact with the internal device of the nRF52 DK (PCA10040) while an other nRF52 connected through the P20 (or P19) connector?
The JLink tool has a "device...
I implemented an application to advertise indefinitely with APP_ADV_TIMEOUT_IN_SECONDS set to 0 and it works just fine. Now I want to
have a time out and set APP_ADV_TIMEOUT_IN_SECONDS...
Reading the nRF51 RM. On page 82 there is this:
But it doesn't make sense to me to talk about the LSByte of the PAYLOAD field, as it's just arbitrary data, and the Radio...
Has anyone had issues with connecting to the nrf52 DK with linux hcitool? I am able to see the device's MAC address and name (using HRM example design) with hcitool lescan...
I have everything working nicely with gcc, my own Makefiles, and the Nordic SDK12.2. I'd like to move to CMake to better automate my process (in particular, compiling one...
Hi
for few days I seem to got stack in using together UART and radio on nRF21LE01 in ESB mode
and I suspect irq_flags = hal_nrf_get_clear_irq_flags(); to be cause of my...
hai,
i am using mbed to program my nrf51822.
i need the following requirements
1.store some data on nrf51822 flash memory using pstorage .
2.setup bonding for security...
It's my question. I use saadc single mode from nrf52832 to sample voltage .When the original voltage is 24 V ,measurement of the pin is 2.8v,I set the resolution to 10 BITS...
