Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I know how to OTA a ble device, but how do this on a ble master?
Is there any nrf tool can OTA a ble master ?
dev environment:
SoftDevices:S130 v2.0.1
sdk: nRF5_SDK_12...
Hi,
we are using a ISP130301 module from Insight SIP (containing a nrf51822CEAA ) with a low power acceleration sensor ADXL362 , connected via SPI. SoftDevice is s130_nrf51_2...
Hi,
SDK: nRF5_SDK_12.2.0_f012efa
No softdevice
Example: nRF5_SDK_12.2.0_f012efa\examples\peripheral\radio\transmitter\pca10040\blank
and receiver.
I have running...
Hello,
I am using nrf51 and firmware is ble_app_gls. I have modified my code to work for dfu as well.
I am getting error as follows
.\_build\nrf51422_xxac.axf: Error...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
Hello,
In our application, we do not use the antenna at Pin30.
However, in Nordic's Reference design in Github, even the simplest design (nRF52832_qfaa_dcdc) has an...
Hello,
Can I interact with the internal device of the nRF52 DK (PCA10040) while an other nRF52 connected through the P20 (or P19) connector?
The JLink tool has a "device...
I implemented an application to advertise indefinitely with APP_ADV_TIMEOUT_IN_SECONDS set to 0 and it works just fine. Now I want to
have a time out and set APP_ADV_TIMEOUT_IN_SECONDS...
Reading the nRF51 RM. On page 82 there is this:
But it doesn't make sense to me to talk about the LSByte of the PAYLOAD field, as it's just arbitrary data, and the Radio...
Has anyone had issues with connecting to the nrf52 DK with linux hcitool? I am able to see the device's MAC address and name (using HRM example design) with hcitool lescan...
I have everything working nicely with gcc, my own Makefiles, and the Nordic SDK12.2. I'd like to move to CMake to better automate my process (in particular, compiling one...
