Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
There is a possible typo in the nRF5340 DK documentation.
https://docs.nordicsemi.com/bundle/ug_nrf5340_dk/page/UG/dk/ext_programming_support_P20.html
In the top picture...
Are there any good tools/apps to commission/provision an ble mesh application that is NLC compliant. Silvair is a great option, but is a closed ecosystem. We are looking for...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Good day,
I tried to build the standard Nordic application: Blinky for the nrf52840dk/nrf52840 board from the following directory on my PC: c:\ncs\v2.9.1\zephyr\samples...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
in prj.conf
I have several warnings in my application that look like this XXXXXXX set more that once. Old Value "x", new value "x". I am worried that this indicates I...
I am facing the following error. I have referered light switch example and have included all the required configs in the prj_fota.conf file
CONFIG_NCS_SAMPLES_DEFAULTS ...
Hello,
I am working on a custom PCB that involves the NRF5340 and our first iteration of PCBs had soldering issues during assembly for the nRF5340. The nRF5340’s footprint...
Hello Nordic,
I am running a project, use the chipset is nRF54L15, I want to know if there is any USB dongle with software can be used to test BLE function of chip nRF54L15...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
