I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I want to collect data for analysis sent from peripheral(ble_app_uart example), I connected peripheral device to app(nrf connect) and enabled service, now the data is sent...
We want to build a network of many nodes (nrf52 boards) distributed in the apartments, that are connected via BLE over 6lowpan, of course using a border router for communication...
image description (/attachment/6196b4481c3f6fefbd0784b78d9163c9)
Hello.
I development education robot by ENTRY base.
PC(ENTRY base) + NRF51822 central
and
NRF51822...
How to develop nrf31512, is it same to the nrf24le1? why i use the same firmware download to the Nrf24le1, it can run normally, but download to the nrf31512 , it can't work...
Hi All,
In my application I have two analog inputs coming from two different sources that I have to sample using one SAADC present inside NRF52. As far as I know, NRF52...
Hi,
I'm using nRF5 SDK V12.0, I found a strange problem. That is the UART can send data to PC, but it cann't receive data from PC. However, this problem just arise on some...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
