Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I'm using a snippet from the ble_app_uart example and see in the examples:
//static ble_uuid_t adv_uuids[1];
static void advertising_init(void)
{
uint32_t err_code;...
S110 v8.0.0
SDK v8.0.0
ble_app_uart example
I first initialize the services and then initialize advertising. Everything works fine when I do NOT advertise the...
I'm currently trying to make an application using the development kit & I'm trying to use the timer driver, when I induled the C & H files of the driver I got an error : ...
I'm trying to compile the ble_app_beacon_s110_pca20006 project in Kile uVision5 and I get the "cannot open source input file "core_cm0.h": No such file or directory" error...
I am trying to run a NRF51822 chip using Emblocks and OpenOCD, the debugger interface is a ST-Link from a Discovery board, which supports SWD.
When I program the Blank...
Hi,
I bumped into a problem trying to get PWM working and traced it back to the app_pwm_init function, for a simple test case use the the pwm example in the 8.1.0 SDK and...
Hello everybody,
I'm currently trying to start with the nordic development kits, I installed all the tools required to be able to start the development & also I get some...
I am trying to persist characteristic data written by the central side after on_disconnect . I can see the data written inside the evt_write->data ptr and I copy it to store...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
Is there any document that describes what has to be done in the App code to migrate from i.e. SDK v7.2 to the latest 8.1.1? I could not find it.
Ideally it would be nice...
