Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
I am using below code to send data over nus. If the data size is 150 bytes, it is OK. However, if the data size is 200 bytes, the nRF51822 will reset. Please tell me how to...
Hello, I got problem in enabling whitelist on starting advertising.
My working enviroment is PCA10028 V1.1.0 2015'18, SoftDevice S130 2.0.1, SDK 12.2.0
MCP works on Android...
Hello,
We encounter the problem after upgraded the PPK software. There are different results when using PPK v1.0.0 and v1.1.0.
Using PPK v1.0.0
Using...
Hi,
There are similar questions posted, but none of them have able to help me out.
I am trying to add multiple base UUIDs in order to create 128-bit UUIDs for my characteristics...
how to create custom service in order to send dummy message, not from the console, I
have to make one char arr[]="hello" this is a fixed string, then where i have add this...
Hi all,
I am developing for the nrf52xx boards. Let's say I want to migrate the example ble_app_uart from SDK v12.2 SoftDevice s132 3.0.0 to SDKv13.0 SoftDevice s132 v4...
Using SDK13
I have a Central program and I included the peer manager code from ble_app_hrs_c but I am having issues after connecting to another dev kit with Peripheral...
Hi,
I'm using nRF51822 with SD130 (SDK 12.1).
I had a firmware based on mbed that had RSSI update, and it was getting quite a few updates per second.
I've now gotten...
SensirionHumiditySensorsSHT3x.pdf
I'm using a Sensirion sensor (see attached datasheet). I'm running SDK 12.2 and SD132. I've set up the TWI to be a master, and I'm using...
Hello !
I'm looking to combine the softdevice into my .hex file generated by Keil.
Currently, when I compile my project, Keil gives me a .hex. To implement this hex file...
Hello, I received my thingy52 and wanted just temperature ...
I see that thingy is not using ESS - environmental sensing service so I tried to create my own.
(I tried to...
(Building with nRF5 12.2.0 / armgcc)
I want to do bursts of pulses using PWM for the pulses and a TIMER to enable the bursts.
I need this to be non-blocking so I can also...
I am interfacing nRF52832 to run ANT protocol in a custom board. Can I use the nRF52832 to broadcast the data received through the UART port without programming the device...
Hi Team,
We are using board PCA10040 wtih nRF52832 SDK 11.
We got nRF5_SDK_11.0.0_freertos_dfu_060516.zip Production SDK which is working fine for me.
I am using project...
Hi folks,
Currently I am able to do secure OTA DFU on my nrf51822 chip (MDBT40) using the example code provided by Nordic SDK 12 (s130). It works charming!
However...
