Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...
We are using a custom board with an nRf9160, and have tested it with several sim cards. The board has been tested with a spectrum analyzer and it is able to transmit RF, however...
I'm having trouble with PDM on SDK15.2 with nRF52840.
The raw data buffers are only half full. The last half are zero's, therefore recorded voice has a robotic sound to...
Hi!
I am trying to use my own repo like described in the tutorial https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect...
I want make connection secure between mobile app and thingy52. What are the types for secure connection. Currently anyone can connect thingy without any permission.
I have setup zephyr development in an ubuntu 18.04 virtual machine. everything is working fine. but can't see the vcp. i disabled and enabled it in the jlink configurator...
Dear Nordic representative,
I would like to run qualification BLE tests on nrf52832 chip: - https://docs.zephyrproject.org/latest/guides/bluetooth/bluetooth-qual.html
...
Dear All,
In my application I need to switch on and off the modem using AT+CFUN=0 and AT+CFUN=4 respectivelly. My question is the following. Let's assume that the device...
SDK:V15
chip:52832
development kit:window+keil
In stm32,inder to use uart rx with DMA, we could easily use:uart Idle interrupt+dma.but how in 52832 while how many...
I’m looking at this example:
https://github.com/NordicPlayground/nrf5-calendar-example
which uses standard C function localtime(), but can not find neither in the example...
