Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hello,
We would like to be able to load the s310 Softdevice via an ANT bootloader. I am using a slightly modified version of experimental_ant_bootloader from the 7.2.0 SDK...
Hi!
Is there any configuration differences between those 2 modules??
I understand from the data sheets that the pinout is just the same.
I´m testing a PA+LNA on the same...
bnjr, je veut mesurer le rssi entre deux composantes BLE Nano . quels son les fichiers .h qu'ils faut ajouter pour le faire fonctionner ?
merci a l'avance
NB : j'utilise...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...
Hi,
Our manufacturer would like to change the recommended capacitors on the nRF51822 antenna circuit design. Here is the query:
Please check below 3 capacitors request...
I notice in the datasheet for the NRF24L01+ that the receive address needs to be programmed into the Receiver.
Our application receives data from another channel and supplies...
Hi All,
I am looking for a cost effective Chip Socket for nRF51822. The challenge with nRF51822 is that while it is the standard QFN48 package, the pitch is 0.4mm making...
hello,
I have known that Nordic has produced new nRF51 DK which already support s130. But it seems only a demo!
What's the exactly plan of BLE 4.1 and 4.2?
When can buy...
Since windows xp isn't supported any more, I need to get the evaluation kit working with a windows 7 PC. It looks like the problem is with the USB communication. Is there...
Hello,
I am using ESB protocol and there is a definition says "#define NRF_ESB_CONST_MAX_TOTAL_PACKETS 6" so how can I use maximum total packets number? I am looking higher...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
