Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
We have some NRF51-DK devices here.
Recently we upgraded our segger software to v5.00.
During programming using nrfjprog we got the question to upgrade the emulator firmware...
I am trying to write a simple advertisement application for my nRF51822 development board (for it to run on an S110), but the tutorial on the nordicsemi.com website, which...
we are making a pedometer. when you are connected, you get notification for every step you make (just an integer)
you just did 50 steps. you can see it in the app. now...
I'm trying to implement a wake-up button on central multilink example. I.e, i need to implement the app_button in order to wake up from sd_evt_wat() function. The problem...
Please can any one tell me from where I can get this programmer? Nordic have stopped selling development boards in which we can get the programmer. I think this could be a...
Hi all!!
sorry to trouble you with this but I work over it for the last 3 days and no breakthrough..
I am using a nRF51DK with the MBED program. I am trying to download...
We are a contract manufacturer. We are trying to help one of our customer's with their bare board design which uses your NRF24L01+ (NRF24L01P) that comes in a 20-pin 4x4mm...
Hi!
We are currently writing a simple bootloader which reads the new application image from a external SPI based flash memory. We are using the S110 SoftDevice, which works...
Hi All,
I have been developing a bluetooth chip based on nRF51822 QFAC. I have followed the design rules very closely but at the end I do not get any bluetooth signal coming...
main.c Hi ,
I'm using nRF51822 and S110 stack and sd_6.0.0.
having an ble app UART example.
Facing a strange problem that when (from nrf Uart App)connecting and disconnecting...
Hi
I set one GPIO interrupt with low-to-high sense, but seems it did not triggle the interrupt when SD run.
I want to confirm the SD would make the interrupt loss? If so...
Hi folks,
I have a 2MHz clock (call it DRDY) coming into my nRF51 on one of the GPIO pins (call it AFE_DRDY). I need to read an external AFE chip on every falling edge...
I have a project where specification requires disconnecting immediately after sending a response to a BLE read request. I'm using authorized reads.
Currently, I'm using...
