Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello
I've been experiencing an unusual problem using the TWI/I2C library for the nRF51-DK board. Basically, I found that I need to shift my device address to the left...
Hi guys,
I have followed devzone.nordicsemi.com/.../ to set up CrossWorks. Even though I got pass the ble_stack_init();, I still can't discover the device for some reasons...
Hi
Please tell me someone me how to start nRF51822 & softdevice8.0.0
I build a NRF51822 application in gcc & ECLIPSE.
When to run the program, it crashes in the boot...
I'm having a problem adding the GPIOTE_IRQhandler() to my main.c file (see attached). I'm getting a compiler error that it is doubly defined in app_gpiote.o and main.o, but...
is it possible to update the pca20006 (rev. 1.2.0 2015.06) beacon with the pca10000 over DFU?
When i tried to update it with my application written for an older version ...
Hi folks,
I'm using the ble_app_template on a custom board. The BSP has a bunch of stuff I don't need, so I would prefer to not use it and handle my I/O directly instead...
i was going through TWI initialization process here i am confused why have we disabled Blocking mode. The reason for Disabling TWI_BlOCKING_DISABLED
I am referring the below...
hi , i want to modify the "transmitter_pca10028" and "receiver_pca10028" examples in SDK to obtain a transmitter/receiver in the same time (tranceiver). So someone have idea...
Hello, I am using the nrf51822EK and I want to combine the ADC and LPCOMP although in the reference manual it says they can not be used at the same time. Is it possible to...
Hi all,
I met one strange thing on SPI interrupt:
when 51822 advertising, the SPI write and read works well;
But, when CONNECTED, with BLE_GAP_EVT_CONNECTED event occured...
Hello,
I migrated my project from softdevice S110 7.1.0 on a nRF51422 FAC to softdevice S110 8.0.0 and an nRF51822 FAA G3. My code used to have a current consumption around...
Hello everyone,
I'm currently using and modifying the experimental_ble_app_uart. I've seen that for sending characters resp commands the file simple_get_uart is used. My...
Good morning.
I'm curently trying to set up an exemple project in Eclipse, but I've tried sevrals tutorials unsuccessfully. Somes are out of date, somes gives me errors...
