We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I am using device as ble-Peripheral SDK nRF51_SDK_7.2.0_cf547b5 and softdevice version :s110_nrf51822_7.1.0_softdevice.
As ble-central SDK nRF51_SDK_7.2.0_cf547b5...
I am currently migrating my projects to SDK 8.0.0.
I have problem with sd_ble_gatts_value_set function.
I receive write request in one characteristic (char.A), and i...
Hello,
I can't find an answer on my question, but maybe I looked over it.
I'm desiging a sensor which will communicate to a smartphone by BLE and to a PC by ANT. The communication...
Hi!
I am using the nRF51822 to do some measurements regarding the capture effect ( en.wikipedia.org/.../Capture_effect).
My question now is: when does the radio latches...
Hi
I´ve got two boards with PIC 18F4620s connected to nRF24L01+ .
One is configured as Tx and the other as Rx.
I can read/write registers trough SPI in both boards, but...
Hi!
Im trying to read the rssi value in real-time from my connected beacon device. Im using a xcode sdk (nRF beacons). All I can find are UUID, Minor and Major values.
...
Hello all.
We have a simple ANT-page application that has the ability to send data as burst packets when requested. The code has been working well. We identified the need...
I'm trying to use nRF51 IoT SDK and setting raspberry pi as router.
When I enter the below command for connecting to nrf51, wlan connection is disconnected.
echo "connect...
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
