But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
I am using SD 8.0 SDK 8.0 and MCP 3.8 I am able to find the DFUtarg service and successfully complete the transfer of my applcation (100% complete). However, upon finishing...
Hi,
I'm doing some throughput/current consumption tests with nRF51822 (on PCA10001).
My firmware has been developed starting from hrm example. I have created a custom service...
Hello,i have nrf518822 device,program the s130 (0.9 version).The centrel connect to the peripherals ,now have a problem.When pressed button1 the {event_handle(BLE_GAP_EVT_CONNECTED...
Hi everyone, I took a nrf51-ble-app-lbs-throughput-test-5.1.0 example from github.com/NordicSemiconductor; I want to send data not only with the push button but even after...
Good day
I can't see my beacon on my phone after downloading the app. The beacon is on but still can't be recognised on the phone.
what might be the problem?
Tsh...
I have an nrf51-DK with an external Temperatur/Humidity sensor. Data is received over I2C. The goal is to save data 6 weeks. I will also need the SoftDevice S110, because...
I will use ADC / Button function over SoftDevice.
below by source.
the thread is repeated not go beyond the conn_params_init.
#define ADC_SAMPLING_INTERVAL APP_TIMER_TICKS...
Hello,
I am working on s130 softdevice(SDK 6.1.0.0 and nRf51822 &nRf51 DK). I have one peripheral and two centrals. but the data from peripheral should be read from only...
I find this function.
tx
void ble_send(uint8_t * data, uint8_t length)
{
ble_nus_send_string(&m_nus, data,length);
}
ble_send(&data_array[0],10);
but I don...
Hi, I'm trying to run ESB during the timeslot api requested slots.
The problem is that BLE uses app_timer, which uses SWI0 for the callbacks, and at the same time, ESB also...
Hey , I am working on nordic nRF51822 chip and using it as an iBeacon. I want to send some custom data apart from UUID,major,minor in the packet. How can I send it ?
As in...
