Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi there,
I found very interesting behavior on casting double variables to integer.
The following code gives me strange result:
double dval = 0.;
int ival = (int...
Hey,
Currently I have been working on a project in which I have to calibrate the range of the bluetooth, basically I need very short range of about a meter.
Could anyone...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
Hi,
The device I am using is nRF52840, WLCSP package. Most of the analog IN pins are noted "low frequency I/O only", e.g. pins A5, A6, C7, C8. - I know there are some exceptions...
Hi,
As of now we are using SEGGER Embedded Studio for compilation and Flashing.
Now we would like to copile using Cmake tool, can you please provide template Cmake for...
downloaded thingysdkv210 from thingy website. extracted that file and executed Prerequisites as per the procedure
downloaded Python v3.xx.xx
downloaded Git v2.xx.xx
...
Hi,
I am trying to add CLI Command feature into the example Open_bootloader_usb_mbr, but get error during link stage when compile as below,
Building ‘open_bootloader_usb_mbr_pca10059_debug...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am using multiple interrupts. For example, BLE communication interrupt and SOC interrupt. I set the priority of each interrupt...
Dear Sir,
I have flashed 'ble_app_hrs' code to one of my RIGADO DK.
I have installed nRFConnect App in mobile phone.
When I press the scan button I could see the device...
Ok I am using GPIO interrupt and want absolute power saving but when I set the GPIO_INTERRUPT_HIGH_ACCURACY to true it works fine but when I set GPIO_INTERRUPT_HIGH_ACCURACY...
Hello,
I want to use P0.27 as output but no way to get it working (tested on my custom board and on DK). If I just change for another pin to check my code, it's OK.
It...
Hi,
I am using nRF SDK v16 with nRF52DK (pca10040) development board.
I've chosen to use RTT logging and I can see my app logs in JLinkRTTViewer window --- however, I...
Hello!
I am developing a FreeRTOS application for nrf52832 with S132 Soft device
Recently I ran out of ram and checked the map-file for clues. The large posts in the mapfile...
Hi,
I don't understand why the characteristic FitnessMachine Feature : (0x2ACC) is not decoded as a bit field by nRF Connect
I can read it and i can see the good value...
