hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
hello everyone
I have some questions with the following function in the hal_aci_tl.cpp file
static bool m_aci_spi_transfer(hal_aci_data_t * data_to_send, hal_aci_data_t...
Throughout twi_hw_master.c, there are lots of places where the code directly accesses PPI channel #0 and thus assumes it's available, as in:
NRF_PPI->CH[0].TEP = (uint32_t...
Hello, I have built a couple of custom boards in the past using the nRF51822 and have stuck very closely to the reference designs. They have all worked.
In my latest board...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
I successfully flashed the experimental_ble_app_uart, I just modified it to do an echo (when I send something with my phone uart app, it give me back the same value...
Since related topic Is BLE changing licensing policy? was marked as resolved I moved my question to new one.
My company is ready to get SIG membership for BLE usage and pay...
I'm creating a custom beacon, similar to iBeacon, but with a custom data format. It advertises only once every 8 seconds, but the iPhone app doesn't receive advertisements...
I tried to read out the temperature sensor of NRF51822. In light CPU load (turn on ADC and send data through BLE every 1s), the measured value is around 45 degC, compared...
I am using the RTC1 compare event to generate a periodic interrupt. When I halt the bugger and and then run the interrupt doesn't occur. Looking at the RTC1 register set shows...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am working on a system where two nRF51 will communicate with use of the ANT protocol (S210). The master and slave must be paired after pressing a button on both sides. I...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
