Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Updating from NCS2.6 to 2.8, the access to my QPSI Flash chip got broken (mx25r64, connected and configured using QPSI exactly as per the nrf5340DK board)
DTS entry:
...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
Hi,
I'm attempting to upgrade an existing project (which is still in the development stage) from NCS 2.7.0 to 3.0.2; this seems to break native TLS, and I'm not sure why...
Hello,
On our custom PCB, we’re using an nRF5340 and an nRF7002 via the WM02C module.
In our devicetree, we are using the following QSPI node configuration.
We’ve produced...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
I'm getting a " Must include ICCID or EID to associate a SIM" message when trying to register a SIM.
And yet the ICCID and PUK have been entered into the form.
What does...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hi Team,
I have added the NUS function in the Matter project. After the commissioning broadcast is turned off, NUS broadcast will automatically start. I want to manually...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Hi
When i used for DK nRF54L15, PMIC nPM1300 was burnout.
and this PMIC i want to directly replace the DK with a new npm1300.
Can the software that comes with this...