Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
I'm having issues executing any Zephyr project on a breadboard connected to a ISP1302. It works fine on the nRF51-DK but anything I try a final hardware nothing happens. Tried...
Hello,
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0...
Hi, Dear Expert:
I am an Electronic Engineer. We used nRF51422 or nRF51822 at our products, but found the products was easily reset when did +/-1KV contact ESD testing...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
Using:
nRF51822
GCC 4.8.4
Nordic Sdk 5.2.0
and even Ole Morten's nice pure-gcc setup
newlib-nano and -flto
Within the startup_nrf51.s I found something...
The server has no I/O, so no way to press a button.
Can an attribute cause the BLE to set a bit in Flash, so at the next power up, it will read that bit and know to execute...
Hello,
I followed the instructions of KEIL in www.keil.com/.../ulink2_trace_itm_viewer.htm
However, I cant get any outputs in Keil Debug(Printf) Viewer using printf...
