Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Just a general plan not a detail one . like this: in the SD132 2.0.0 we will add the funtion of change the MTU up to about 150 bytes，at the approximate time 2016-4
I am testing the freertos port, based on the hrs example in the new SDK 10.0. I have run into an issue while using the uart during long transmission sequences (where the fifo...
The alpha release of the S332 is now available and I am just curious which example included in the 0.9.2 SDK would be the best jumping off point for building a new project...
I just realized that I have the nrf52 board (with nrf25832) which actually explains a lot but the end goal of my project will be using the nrf51822 (because the nrf52 chip...
Hi there,
I am using the nrf51-ble-driver_win_0.5.0 to communicate with peripherals via the PCA10028.
My problem is when I call sd_ble_gattc_write() in my Windows application...
Hello Everyone,
I am trying to add the pwm library in the button example in SDK verrsion 10 but app_pwm.c files showing this error can anyone letme know why this error is...
I use s130 based device as central to connect to my ios device, when connected, the central will issue a bond request, if user accept this request on ios device, the bond...
While using PPI and trying to use the first channel as a clock based PWM running on timer1 I noticed that whenever I use more than 2 PPI channels, the pin that is toggeling...
Hello!
I have multiple peripherals and multiple centrals. I'm trying to make one peripheral to connect only to one central.
I read a way to do this is by using whitelisting...
I’m attempting to use an nRF51 dongle with connectivity_115k2_with_s130_1.0.0.hex burned on to it. I’m using the dongle as a central, attempting to connect to a peripheral...
Hi, i try to add a passkey with "ble_app_uart".
I want to this thing.
If i try to use the master_pannel app to connect, peripheral require passkey.
no bonding.
...
Hi all;
I have a hardware question . How much is the discharge time of 10uF capacitor which put in the VDD pin of 51822 ?
When i use the formula of capacitor discharge...
I need to do this, A product ble and Gazell should be used. Switch bluetooth or Gazell mode by pressing the button, but ble and Gazell not used the same time.
When I switch...
condition:i am using the nrf51_adk10.0.0,and i want to enable the NRF51422 as a central role.,so a program the sd130,and i download the application into the board(ble_app_uart_c_s130_pca10028...
Hello,
I am using nRF51822 to build a product and employ 3.0V battery as power supply and system works on DCDC mode. I need RTC counter to do real time tracking. My question...
