Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I am using proximity profile for my custom board as a tracker.I would like to make the services read/write operations accessable only to my andriod app.Others can connect...
Hello,
Recently I purchased a BLE Nano Kit with MK20/ DAP Link USB Board - Bluetooth 4.0 Low Energy Module Development Board from Fab2Lab and I was trying to use the nRF...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
Dear all,
I have a project with a nRF51822 based on S110 and SDK10.
Almost everything is running fine, but every time I scan for devices, either by calling BluetoothAdapter...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
Hi,
in want to extend the DFU library (Android and iOS) with a function similar to setBinOrHex(). But instead of a filename, i want to give a byte array with the init packet...
I think there is a bug in Nordic provided code in this thread about fetching the offending PC in a hardfault handler:
devzone.nordicsemi.com/.../
The provided code is...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
