hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
hi, i am a beginer in BEL application.
after some tries, i can compile and download 'ble_app_uart'.
but the module does not work at all also it dosen't advertising....
...
i make a new "Makefile! project" using example in SDK first i use the "blinky" ,
it looking likes can be work, then i try to use " blr_app_hrs_c " ,
i do the same step to...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
I'm trying to develop a minimalist android app to send and receive data with my nrf51822 dev-board.
Can anyone please tell me where I can find a great project example?...
Hello,
In our project i am using nrf51822 with stack Softdevice S110 . We want to connect it with Samsung Gear S2.Is it possible with stack s110 or i have to use stack...
When the device powers up I want to grab the device name from a known location and also rewrite that same location when I get a new device name. How can I write to the internal...
Suppose you want to send 20 bytes of data using API sd_ble_gatts_hvx, do you need to punctuate the first 16 or so data within the 20 bytes sent with a CRC ?
it may seem...
Hi, all. I use nrf52 and softdevice(S132).
I'd like to know SoftDevice process timing to hardware.
Can it be ?
I know, SoftDevice Specification in "Processor availability...
Hello,
I have an development kit NRF51 and wrote a code for it which uses uart, ble advertising and ble scan. It works pretty well on the kit.
The problem is when I...
Hi,
I use a personnal GAP Address, but it must be the type used:
-Public address.
-Random Static address.
-Private Resolvable address.
-Private Non-Resolvable address...
Hi,
I am trying to get the dfu single bank bootloader ( github.com/.../nrf51-dfu-single-bank-ble) supplied by Nordic to work. I can successfully push firmware to my device...
Hi, I am just trying to understand the examples properly. This value is mostly set to 0, sometimes set to 1, and used at the call to the soft device initialization.
ble_enable_params...
