Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
Hi all,
first of all I'm new to NRF and BLE applications so I'm truly sorry if some of my questions are very basic and if answer to some of them is already posted somewhere...
Hi all,
I am using pins P0.00, p0.01, p0.09 and p0.10 in my application. I wandering why these pins are not functioning as GPIO. I have searched various links such as ...
Hi，everyone！I am using nRF connect mesh for Mesh DFU(see this link text ), and I follow the direction step by step. But, the nRF connect can't find any device to program....
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am running into trouble Writing...
